Keurig Won’t Turn On? Official Power Checks and Fixes

Quick answer: most Keurigs that “won’t turn on” are switched off by Auto Off, not broken. Press the power button (or lift and lower the handle on models with Smart Start), and make sure the brewer is plugged into its own grounded outlet. If it powers on but won’t brew, add water and re-seat the reservoir.

1. Check whether it’s off or just asleep

Current Keurig brewers turn themselves off to save energy. The K-Express and K-Supreme Plus guides both say Auto Off turns the brewer off 5 minutes after the last brew. Press the power button and it’s ready again. On these models, lifting and lowering the handle with water in the reservoir also powers the brewer on.

Keurig 2.0 brewers such as the K500 series have Auto On, Auto Off and Energy Saver settings (Energy Saver turns the brewer off in 15-minute steps after the last brew). If yours switches off at the same time every day, check those settings first.

2. Keurig’s official power checks

  1. Make sure the power button is actually on.
  2. Plug the brewer into its own grounded outlet. Keurig says that if the circuit is overloaded with other appliances, the brewer may not work properly, so run it on its own circuit.
  3. If it still has no power, Keurig’s guides say to contact Keurig Customer Service.

General electrical checks (not from Keurig’s guides): plug a lamp or phone charger into the same outlet to confirm it works. Kitchen outlets are often GFCI outlets, so press the outlet’s RESET button if it has tripped, and check your breaker panel. Don’t use a damaged cord or plug.

3. It turns on but won’t brew

  • Not enough water: the K-Supreme Plus needs at least 6 oz in the reservoir. Keurig’s fix: add 2 oz more and press brew (or the size button on a K-Express), and repeat until it dispenses.
  • Reservoir not seated: lift the reservoir off and put it back so it sits securely on the base (on the K500 series, make sure the lock tabs engage).
  • Reservoir removed mid-brew (K500 series): replace it and run a rinsing brew without a pod.
  • Short cups or no flow: the exit needle may be clogged. Clean it with a straightened paper clip (needle cleaning steps), then descale if needed.

Model-specific steps from Keurig’s guides

ModelPowering onAuto offPartial-cup purge
K-ExpressPower button; lifting and lowering the handle also powers it on5 minutes after the last brewPower off, hold the 12oz button 5 seconds until water dispenses, discard, power on
K-Supreme PlusLift the handle (Smart Start) or press the power button5 minutes after the last brewPower off, hold brew + 12oz for 5 seconds until water dispenses, discard, power on
K500 series (2.0)Power button; preheating takes about 3 minutes at first setupSet in the menu: Auto Off / Energy Saver (15-minute steps)Clean the exit needle; replace the reservoir if removed and run a rinsing brew

4. After descaling, it won’t fill or brew

A heavily scaled brewer may not fill once descaler is added: you get little or no output and hear air. Keurig’s fix is to turn it off and unplug it, discard the solution, rinse and refill the reservoir with water, then repeat the fresh-water rinse. If the problem continues, leave the brewer unplugged for at least 30 minutes before trying again. More fixes: Keurig not working after descaling.

When to stop and contact Keurig

If the brewer still has no power after these checks, contact Keurig Customer Service, as the guides instruct. Unplug it right away and don’t keep using it if it trips the breaker, smells of burning or the cord is damaged. Keurig’s guides say the brewer is not user-serviceable beyond the cleaning and maintenance steps.

Guides for specific Keurig models

Sources: Keurig K-Express Use & Care Guide, K-Supreme Plus Use & Care Guide and K500 series guide (checked November 21, 2026). Steps differ by model, so use your own brewer’s guide if it isn’t covered here.

Leave a Reply

Your email address will not be published. Required fields are marked *